Echelon PCLTA-21 Guida Utente

LONWORKS® PCLTA-20 PCI Interface User’s Guide Version 3 C o r p o r a t i o n 078-0179-01C

1-4 Introduction The card also permits the host PC to act as a LONWORKS network device, running application-specific programs while the card handl

PCLTA-20 PCI Interface User’s Guide 2-1 2 Installing the PCLTA-20 Card This chapter describes the procedures for installing the PCLTA-20 card.

2-2 Installing the PCLTA-20 Card PCLTA-20 Card Software Installation There are three versions of the PCLTA-20 installation software, one for Windo

PCLTA-20 PCI Interface User’s Guide 2-3 Windows 95/98/Me Software Installation Procedure To install the PCLTA-20 software on a Windows 95/98/Me PC,

2-4 Installing the PCLTA-20 Card 8. If the installation software discovers the SYSTEM.INI entry that loads the ECHLMPA.386 ISA bus driver, it wil

PCLTA-20 PCI Interface User’s Guide 2-5 6. When prompted for a destination directory, enter the desired installation directory. By default this di

2-6 Installing the PCLTA-20 Card 5. If necessary, edit the CONFIG.NT file to remove any references to the PCLTADOS.SYS driver. Windows 95/98/Me

PCLTA-20 PCI Interface User’s Guide 2-7 The following is an example of the line that would be added to the CONFIG.NT file: DEVICE=C:\LONWORKS\BIN\PCL

2-8 Installing the PCLTA-20 Card Installing the PCLTA-20 Card Before Software Installation The following section applies to Windows 95/98/Me only

PCLTA-20 PCI Interface User’s Guide 2-9 Access the hardware conflict troubleshooter through the procedure outlined below: 1. Open the Windows 95/98/

Echelon, LON, LONWORKS, LonTalk, LonBuilder, NodeBuilder, LONMARK, Neuron, LonManager, 3120, and 3150 are trademarks of Echelon Corporation regist

2-10 Installing the PCLTA-20 Card An additional problem often associated with sound cards is the improper reporting of I/O resource usage. This p

PCLTA-20 PCI Interface User’s Guide 2-11 3. On the following line, add the following driver alias: aliasname=devicename where aliasname is the

2-12 Installing the PCLTA-20 Card LonMaker Integration Tool or any other LNS tool does not work. You will notice that when the network is open t

PCLTA-20 PCI Interface User's Guide 3-1 3 Configuring and Testing the PCLTA-20 Card This chapter explains how to configure and test the PCLTA-20

3-2 Configuring and Testing the PCLTA-20 Card PCLTA-20 Configuration PCLTA-20 configuration is accomplished by using the LONWORKS Plug ‘n Play contr

PCLTA-20 PCI Interface User's Guide 3-3 suggested by the error message, produces the diagnosis: “Image file not found.” In this case, return to

3-4 Configuring and Testing the PCLTA-20 Card • NSIPCLTA, the LNS network interface image (for use with LNS 1 and LNS 2 only) • PCC10L7, the basic

PCLTA-20 PCI Interface User's Guide 3-5 When configuring a custom transceiver or adding custom parameters for a standard transceiver, the Custom

3-6 Configuring and Testing the PCLTA-20 Card Enable PC Card Reset This control is not used with the PCLTA-20 card. It is provided for owners of the

PCLTA-20 PCI Interface User's Guide 3-7 Priority: the priority application output buffer count, as calculated by the driver based on informatio

FCC NOTICE (for USA only) Federal Communications Commission Radio Frequency Interference Statement Warning: This equipment has been tested and found

3-8 Configuring and Testing the PCLTA-20 Card -- Network Interface Node Status -- CRC Errors: [00000] TX Timeouts: [00000] Lost (APP) Messages: [0

PCLTA-20 PCI Interface User's Guide 3-9 per second until either the OK or the Quit button is chosen (the Quit button will appear in place of the

3-10 Configuring and Testing the PCLTA-20 Card

PLCTA-20 PCI Interface User’s Guide 4-1 4 Electrical and Mechanical Interfaces This chapter describes the hardware interfaces and mechanical layout

4-2 Electrical and Mechanical Interfaces PCLTA-20 Board Layout Figure 4.1 shows the layout of the PCLTA-20 card Models 74401, 74402, 74403, and 744

PLCTA-20 PCI Interface User’s Guide 4-3 Figure 4.3 shows the layout of the PCLTA-20/SMX Interface and the PCLTA-20 Protocol Analyzer Card. These card

4-4 Electrical and Mechanical Interfaces accept 12 to 26AWG (1.2mm to 0.45mm) wire. The terminals are connected as follows (with terminal 3 being c

DECLARATION OF CONFORMITY PC LonTalk® Adapater, PCLTA-20 Application of Council Directive: 89/336/EEC Manufacturer’s Name:

PCLTA-20 PCI Interface User's Guide iii Contents 1 PCLTA-20 Introduction 1-1 Introduction 1-3 Audience 1-4 Content 1-4 R

iv Echelon Transceiver 3-4 Diagnostics 3-5 General Settings 3-5 System Image Path 3-5 Layer2 and Layer6 Buffering

PCLTA-20 PCI Interface User’s Guide 1-1 1 PCLTA-20 Introduction This guide describes the mechanical characteristics and the hardware and software

1-2 Introduction TP/FT-10 free topology and PL-10, PL-20, and PL-30 power line channels. The PCLTA-20 card can be used as an LNS Fast Network Int

PCLTA-20 PCI Interface User’s Guide 1-3 Introduction The PCLTA-20 card provides any PC equipped with a 32-bit PCI interface and compatible Windows